PAROC AluCoat Tape

PAROC AluCoat Tape TI13101
PAROC AluCoat Tape is a reinforced aluminum foil tape with pressure sensitive, low temperature acrylic adhesive, siliconized release paper liner and AluCoat printing. Ideal for sealing joints when using PAROC AluCoat products such as sections, lamella mats or slabs. PAROC Tape AluCoat gives a great finish and safe installation.

Datasheet

 
Updated 15 May 2019

Width
50, 75 and 100 mm
Length
50 m
Volume
Rolls / carton: 50mm / 24 pcs, 75mm / 16 pcs, 100mm / 8 pcs. 24 cartons/pallet.

Other Properties

Other Properties
PropertyValue
AdhesiveLow temperature acrylic
. 
Release linerSiliconized paper
. 
Temperature range-35 °C to +120 °C
. 
Storage conditions+18 °C ÷ 25 °C, under dry conditions inside a warehouse
. 
Installation temperature-20 °C ÷ 40 °C

Facings

Facing Material
Background: Reinforced aluminum foil

Colours

Aluminum, bright with AluCoat printing

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of +5 Celsius. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry free of dust and grease. Surface must be free from oil, fat, dust and solvents before film/tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources.

More Information

We strongly advise users to test the product ‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test results and practical experience and are aimed at helping customers select the appropriate tape for a given application. This information is provided without liability. We reserve the right to change the technical specification without prior notice.

Width
50, 75 and 100 mm
Length
50 m
Volume
Rolls / carton: 50mm / 24 pcs, 75mm / 16 pcs, 100mm / 8 pcs. 24 cartons/pallet.

Other Properties

Other Properties
PropertyValue
AdhesiveLow temperature acrylic
. 
Release linerSiliconized paper
. 
Temperature range-35 °C to +120 °C
. 
Storage conditions+18 °C ÷ 25 °C, under dry conditions inside a warehouse
. 
Installation temperature-20 °C ÷ 40 °C

Facings

Facing Material
Background: Reinforced aluminum foil

Colours

Aluminum, bright with AluCoat printing

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of +5 Celsius. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry free of dust and grease. Surface must be free from oil, fat, dust and solvents before film/tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources.

More Information

We strongly advise users to test the product ‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test results and practical experience and are aimed at helping customers select the appropriate tape for a given application. This information is provided without liability. We reserve the right to change the technical specification without prior notice.

Width
50, 75 and 100 mm
Length
50 m
Volume
Rolls / carton: 50mm / 24 pcs, 75mm / 16 pcs, 100mm / 8 pcs. 24 cartons/pallet.

Other Properties

Other Properties
PropertyValue
AdhesiveLow temperature acrylic
. 
Release linerSiliconized paper
. 
Temperature range-35 °C to +120 °C
. 
Storage conditions+18 °C ÷ 25 °C, under dry conditions inside a warehouse
. 
Installation temperature-20 °C ÷ 40 °C

Facings

Facing Material
Background: Reinforced aluminum foil

Colours

Aluminum, bright with AluCoat printing

Installation

During the installation, the insulation material to be taped should be at a minimum temperature of +5 Celsius. Allow the temperature of the insulating material to adjust to the ambient installation temperature. Make sure that the surfaces to be joined with tape are clean, dry free of dust and grease. Surface must be free from oil, fat, dust and solvents before film/tape application. Do not use cleaners containing anti-adhesive agents. Some plastics and paints may discharge anti-adhesive agents leading to bonding failure. Rough and uneven surfaces may weaken bonding.

Handling and Storage

Product should be stored in original packaging, laid flat on the slit edge of the roll. Storage in dry and clean areas, at normal temperature, protected from direct sunlight and heat sources.

More Information

We strongly advise users to test the product ‘s suitability for their own particular requirement. All data and recommendations contained in this Technical Data Sheet are based on our own test results and practical experience and are aimed at helping customers select the appropriate tape for a given application. This information is provided without liability. We reserve the right to change the technical specification without prior notice.